English   Japanese   
TOP         PRODUCTS         TECHNOLOGY         DISTRIBUTORS         PRODUCT STATUS
     MOTORIZED CONTROL FADER

in planning LMH6-100 Series
Direct print resistor element used (Special surface treatment).
Double resistance circuit type
Thin body 13mm
Horizontal style control-bar design (Protection against dust).
Connector terminal style
Last update: 2025.0X.21. [Specifications] [Note] [Dimensions] [Model-number] [Update list] EU-RoHS


Information
This data sheet is under development.

Usage is the same as for LMH5-1101.


Electrical specifications
(initial value)		 LMH6-100 Series
Products LMH6-100-B**K-M8V-C1 LMH6-100-B**K-M8V-C2
Number of circuits
Type of output law
 1
Law: Linear taper (Double linear)
Circuit method (Output law) Potentiometer circuit
Total resistance (1-3) 10kohm (20kohm x2),   5kohm (10kohm x2)
Total resistance tolerance ±20%
Absolute linearity ±5% (The travel is divided into 10 sections and 11 positions are measured.)
Residual voltage (1-2), (2-3) 20mV or less
Residual resistance (1-2), (2-3) 50ohm or less (Reference values)
Touch sense track contact
resistance		 30ohm or less (Between terminal T and Control-bar.)
 
Voltage proof 1 Min. at AC500V
Insulation resistance 50Mohm or more at DC100V
Max rating 0.2W
Maximum input voltage DC30V or less
Sliding noise level 47mV or less (by JIS C 6443)
Sliding life 100,000 Cycles Min. (18cycles/min, Sliding noise level: Less than 100mV)
Drive motor data
 		 DC8V Iron cored motor : Input voltage: DC5V - 11.5V (Nominal DC8V), Stall current: 0.5A or less
[FF-050SB-09250 : MABUCHI MOTOR Co., Ltd.]
Connector style
 		  B7B-EH (JST)
* Including motor lines		 B5B-EH (JST)
 

Mechanical specifications
(initial value)		 LMH6-100 Series
Travel (Stroke) length 100mm ±0.5mm
Operating force 0.1 to 0.3N
Strength Nut-Attached 100Ncm
Attached parts M3 screw (Length: Panel thickness + 3mm)
Stopper strength 30N
Push-pull strength 30N
Alignment to the center ±0.5mm (State not to pressure control-bar, Measurement position: Mounting surface)

General specifications LMH6-100 Series
Temperature range -10 to +50 degrees C (Operating), -15 to +60 degrees C (Storage)
Relative humidity 80%RH (No condensation)


Please check before use.
* Solder heat resistance: 350deg C max, 5sec max, 2 times. (Manual soldering only)
* Please take care during soldering that the smoke from the solder does not flow inside a fader.
* If the flux sticks to a resistor board, it may cause a trouble with the fader.
* Move to one end in Control-bar on the occasion of knob wearing, and can break into it slowly.
* It is highly recommended that the fault tolerant system is to be set up in the big situation like the live broadcast.
* This product is designed on the assumption of the horizontal use.
* The enough operational testing is highly recommended for the slant or the vertical use to prevent the unexpected operation.
* Replacing it from other brands tests it enough, and please consider.
The load resistance (R) on the fader output side should be much higher than 20 times the total resistance value.

During fader operation, due to noise generated from friction between resistive elements and contacts
and noise generated from vibration of the power mechanism, there are many factors affecting the output signal quality.

To reduce these effects, use decoupling capacitors (C).
(Use a capacitor value that matches the control circuit to which it is connected.)
* It is recommended that motor leads be shortened and twisted.
  Consider not to interfere with other motor leads.
* Color may vary slightly due to body material.
* Due to the way the body is processed, there may be some rubbing on the folded parts.
* Please do not strike the fader carriage hard against either end of the fader.
* Please do not stop the fader keeping the fader carriage pushed hard against either end of the fader.


Outline - LMH6-100-B**K-M8V-C1

Outline - LMH6-100-B**K-M8V-C2

Panel cut out

Terminations


Model number
LMH6-100 - B 10K - M8V - C1
*1   *2 *3   *4   *5


*1 Product number (travel) LMH6-100 : 100mm
*2 Output law B : Linear taper + Touch sense track
*3
 		 Total resistance
 		 10K : 10kohm
5K   : 5kohm
*4 DC Motor type M8V : DC8V Iron cored
*5
 		 Connector style (Please see dimension)
 		 C1 : B7B-EH (JST) * Including motor lines
C2 : B5B-EH (JST)


Products No.
( X: Standard model)		 Travel Output law Resistance value Touch sense
track		 Motor Mounting
Screws		 Control-bar length
(Bracket height)
LMH6-100-B10K-M8V-C1 X 100mm Linear 10kohm With DC8V
iron cored		 M3 9mm (5mm)
LMH6-100-B5K-M8V-C1 X 100mm Linear 5kohm With DC8V
iron cored		 M3 9mm (5mm)
LMH6-100-B10K-M8V-C2 X 100mm Linear 10kohm With DC8V
iron cored		 M3 9mm (5mm)
LMH6-100-B5K-M8V-C2 X 100mm Linear 5kohm With DC8V
iron cored		 M3 9mm (5mm)




Update list
   
2025.0X.21. First edition