| MOTORIZED CONTROL FADER |
 |
LMA5-2000 Series |
| Direct print resistor element used (Special surface treatment). Vertical style control-bar design. PCB Terminal style. All models include a touch sense track. |
| Last update: 2023.12.19. | [Electrical-spec] | [Mechanical-spec] | [Note] | [Dimensions] | [Model-number] | EU-RoHS |
| Information |
| This product is compatible with MLA-Series. |
| Electrical specifications (initial value) |
LMA5-2000 Series | |
| Products | LMA5-2101*-B*-* | LMA5-2601*-B*-* |
| Number of circuits Type of output law |
1 Law1: Linear taper |
|
| Circuit method (Output law) | Potentiometer circuit | |
| Total resistance (1-3) | 10kohm, 5kohm | |
| Total resistance tolerance | ±20% | |
| Absolute linearity | ±5% (The travel is divided into 10 sections and 11 positions are measured.) | |
| Residual voltage (1-2), (2-3) | 20mV or less | |
| Residual resistance (1-2), (2-3) | 50ohm or less (Reference values) | |
| Touch sense track contact resistance |
30ohm or less (Between terminal T and Control-bar.) |
|
| Voltage proof | 1 Min. at AC500V | |
| Insulation resistance | 50Mohm or more at DC100V | |
| Max rating | 0.2W | |
| Maximum input voltage | DC30V or less | |
| Sliding noise level | 47mV or less (by JIS C 6443) | |
| Sliding life | 100,000 Cycles Min. (18cycles/min, Sliding noise level: Less than 100mV) | |
| Drive motor data |
DC8V Iron cored motor : Input voltage: DC5V - 11.5V
(Nominal DC8V), Stall current: 0.5A or less [FF-050SB-09250 : MABUCHI MOTOR Co., Ltd.] |
|
| Mechanical specifications (initial value) |
LMA5-2101 Series | LMA5-2601 Series |
| Travel (Stroke) length | 100mm ±0.5mm | 60mm ±0.5mm |
| Operating force |
0.1 to 0.3N 0.15 to 0.4N (With dust cover) |
|
| Strength Nut-Attached | 100Ncm | |
| Attached parts | M3 screw (Length: Panel thickness + 3~5mm) | |
| Stopper strength | 30N | |
| Push-pull strength | 30N | |
| Alignment to the center | ±0.5mm (State not to pressure control-bar, Measurement position: Mounting surface) | |
| General specifications | LMA5-2000 Series |
| Temperature range | -10 to +50 degrees C (Operating), -15 to +60 degrees C (Storage) |
| Relative humidity | 80%RH (No condensation) |
| Note |
| * Solder heat resistance: 350deg C max, 5sec max, 2 times. (Manual
soldering only) * Please take care during soldering that the smoke from the solder does not flow inside a fader. * If the flux sticks to a resistor board, it may cause a trouble with the fader. |
| * Move to one end in Control-bar on the occasion of knob wearing, and can break into it slowly. |
| * It is highly recommended that the fault tolerant system is to be set up in the big situation like the live broadcast. |
| *
This product is designed on the assumption of the horizontal use. * The enough operational testing is highly recommended for the slant or the vertical use to prevent the unexpected operation. |
| * Replacing it from other brands tests it enough, and please consider. |
| * The type with dust-cover rubs against dust-cover and control-bar, which changes operating force and the feel of the product. |
| * It is recommended that motor leads be shortened and twisted. Consider not to interfere with other motor leads. |
| * Color may vary slightly due to body material. * Due to the way the body is processed, there may be some rubbing on the folded parts. |
| Dimensions - LMA5-2101-B**-M8V | ||||
 |
||||
|
| Dimensions - LMA5-2601-B**-M8V | ||||
 |
||||
|
| Dimensions - Panel cut out |
 |
| Dimensions - P.C.Board Mounting hole detail (Viewed from mounting side) |
 |
| Dimensions - Terminations |
 |
| Model number | ||||||||||||||||
|
| *1 |
Product number (travel) |
LMA5-210 : 100mm LMA5-260 : 60mm |
| *2 | Control-bar length: Length (Bracket height) | 1 : 9mm (5mm) |
| *3 |
Option: Dust cover |
Blank : Without D : With |
| *4 | Output law | B : Linear taper + Touch sense track |
| *5 |
Total resistance |
10K : 10kohm 5K : 5kohm |
| *6 | DC Motor type | M8V : DC8V Iron cored |
| Products No. ( X: Standard model) |
Travel | Output law1 |
Resistance law1 |
Dust cover | Touch sense track |
Motor | Mounting Screws |
Control-bar length (Bracket height) |
|
| LMA5-2101-B10K-M8V | X | 100mm | Linear | 10kohm | Without | With | DC8V iron cored |
M3 | 9mm (5mm) |
| LMA5-2101-B5K-M8V | 100mm | Linear | 5kohm | Without | With | DC8V iron cored |
M3 | 9mm (5mm) | |
| LMA5-2101D-B10K-M8V | 100mm | Linear | 10kohm | With | With | DC8V iron cored |
M3 | 9mm (5mm) | |
| LMA5-2101D-B5K-M8V | 100mm | Linear | 5kohm | With | With | DC8V iron cored |
M3 | 9mm (5mm) | |
| LMA5-2601-B10K-M8V | X | 60mm | Linear | 10kohm | Without | With | DC8V iron cored |
M3 | 9mm (5mm) |
| LMA5-2601-B5K-M8V | 60mm | Linear | 5kohm | Without | With | DC8V iron cored |
M3 | 9mm (5mm) | |
| LMA5-2601D-B10K-M8V | 60mm | Linear | 10kohm | With | With | DC8V iron cored |
M3 | 9mm (5mm) | |
| LMA5-2601D-B5K-M8V | 60mm | Linear | 5kohm | With | With | DC8V iron cored |
M3 | 9mm (5mm) | |
| Update list | |
| 2023.12.19. | Addition of maximum input voltage specification. Change in maximum ratings. |
| 2023.09.13. | Dimensions changed due to a change in the terminal manufacturer. [4.3 → 4.9] |
| 2023.08.04. | Added note on motor leads and body material. |
| 2023.03.17. | Additional 3D data (step format). |
| 2023.03.04. | Correction of erroneous listing of terminal length. [4.8 → 4.3] |
| 2023.02.20. | First edition |