| CROSS FADER |
 |
CFX-45L Series |
| Conductive plastic resistor element used (Low slide noise). Horizontal style control-bar design (Protection against dust). Durable system which adopted the shaft of the high quality. 2-type terminal style. |
| Last update: 2024.01.23. | [Electrical-spec] | [Mechanical-spec] | [Note] | [Dimensions] | [Model-number] | EU-RoHS |
| Information |
| Electrical specifications (initial value) |
CFX-45L Series |
| Products | CFX-45L*-B* |
| Number of circuits Type of output laws |
2 Linear taper x2 |
| Circuit method | Potentiometer circuit |
| Total resistance (1-2), (6-4) | 10kohm, 50kohm |
| Total resistance tolerance | ±20% |
| Absolute linearity | ±5% |
| Residual resistance (1-3), (2-3), (6-5), (5-4) |
5ohm or less |
| Voltage proof | 1 Min. at AC100V |
| Insulation resistance | 50Mohm or more at DC250V |
| Max rating | 0.1W |
| Maximum input voltage | DC30V or less |
| Sliding noise level | 47mV or less (by JIS C 6443) |
| Sliding life | 100,000 Cycles Min. (18cycles/min, Sliding noise level: Less than 100mV) |
| Connector (6pin) | S6B-EH (EH Series: J.S.T.MFG.CO.,LTD.) |
| Mechanical specifications (initial value) |
CFX-45L Series |
| Travel (Stroke) length | 45mm ±0.5mm |
| Operating force | 0 to 0.2N |
| Strength Nut-Attached | 100Ncm |
| Attached parts | M3 screw (Length: Panel thickness + 3mm) |
| Stopper strength | 40N |
| Push-pull strength | 40N |
| Alignment to the center | ±0.5mm (State not to pressure control-bar, Measurement position: Mounting surface) |
| General specifications | CFX-45L Series |
| Temperature range | -10 to +60 degrees C (Operating), -15 to +65 degrees C (Storage) |
| Relative humidity | 80%RH (No condensation) |
| Note |
| * Solder heat resistance: 350deg C max, 5sec max, 2 times. (Manual
soldering only) * Please take care during soldering that the smoke from the solder does not flow inside a fader. * If the flux sticks to a resistor board, it may cause a trouble with the fader. |
| * Move to one end in Control-bar on the occasion of knob wearing, and can break into it slowly. |
| * Replacing it from other brands tests it enough, and please consider. |
| Dimensions - CFX-45L-B* | ||
 |
||
|
| Dimensions - CFX-45LN-B* | ||
 |
||
|
| Dimensions - Panel cut out |
 |
| Dimensions - Terminations / Output law |
 |
| Model number | ||||||||||||
|
| *1 | Product number | CFX-45 : CFX-45L Series |
| *2 | Residual resistance | L : Low residual resistance |
| *3 |
Terminal styale |
Blank : Connector N : Soldering terminal |
| *4 | Output law | B : Linear taper |
| *5 |
Total resistance |
10K : 10kohm 50K : 50kohm |
| Products No. ( X: Standard model) |
Travel | Output law | Resistance | Mounting screws | Terminal style | |
| CFX-45L-B10K | X | 45mm | Linear | 10kohm | M3 | Connector |
| CFX-45L-B50K | X | 45mm | Linear | 50kohm | M3 | Connector |
| CFX-45LN-B10K | X | 45mm | Linear | 10kohm | M3 | Soldering |
| CFX-45LN-B50K | X | 45mm | Linear | 50kohm | M3 | Soldering |
| Replacement model | Photo | Connector | Compatible with replacement crossfader |
| CFX-45L-B50K-CN1 |
 |
22-27-2041 (Molex) Wire: 50mm |
Vestax CF-PCV (Switch mode "PMC") |
 |
|||
| Update list | |
| 2024.01.23. | Addition of replacement model. |
| 2023.12.19. | Addition of maximum input voltage specification. |
| 2023.07.20. | Slight correction of specification notations. |
| 2023.05.08. | Correction of erroneous listing of terminal length. [5.1 → 3.5], Additional 3D data (step format). |
| 2022.11.08. | First edition |