| CROSS FADER |
 |
45LT-R2 Series |
| Direct print resistor element used (Special surface treatment). Equipped with a torque adjustment mechanism with good feel. Horizontal style control-bar design. Durable system which adopted the shaft of the high quality. Connector terminal style. |
| Last update: 2024.01.29. | [Electrical-spec] | [Mechanical-spec] | [Note] | [Dimensions] | [Model-number] | EU-RoHS |
| Information |
| Electrical specifications (initial value) |
45LT-R2 Series |
| Products | 45LT-R2-CN0-B* |
| Number of circuits Type of output laws |
1 Linear taper |
| Circuit method | Potentiometer circuit |
| Total resistance (1-2), (6-4) | 10kohm, 50kohm |
| Total resistance tolerance | ±20% |
| Absolute linearity | ±5% |
| Residual resistance (1-3), (1-4) | 60ohm or less |
| Voltage proof | 1 Min. at AC100V |
| Insulation resistance | 50Mohm or more at DC250V |
| Max rating | 0.1W |
| Maximum input voltage | DC30V or less |
| Rated Resistive Load - Switch | AC125V 3A, DC30V 2A (OMRON D2F-F) |
| Sliding noise level | 47mV or less (by JIS C 6443) |
| Sliding life | 100,000 Cycles Min. (18cycles/min, Sliding noise level: Less than 100mV) |
| Connector (4pin) | B4B-EH (EH Series: J.S.T.MFG.CO.,LTD.) |
| Mechanical specifications (initial value) |
45LT-R2 Series |
| Travel (Stroke) length | 44mm ±0.5mm |
| Operating force |
0 to 0.1N 0 to 0.5N (Torque adjustment screw) |
| Strength Nut-Attached | 100Ncm |
| Attached parts | M3 screw (Length: Panel thickness + 3mm) |
| Stopper strength | 50N |
| Push-pull strength | 50N |
| Alignment to the center | ±0.5mm (State not to pressure control-bar, Measurement position: Mounting surface) |
| General specifications | 45LT-R2 Series |
| Temperature range | -10 to +60 degrees C (Operating), -15 to +65 degrees C (Storage) |
| Relative humidity | 80%RH (No condensation) |
| Note |
| * Move to one end in Control-bar on the occasion of knob wearing, and can break into it slowly. |
| * Replacing it from other brands tests it enough, and please consider. |
| Dimensions - 45LT-R2-CN0-B* |
 |
| Dimensions - Torpue ajustment screw |
 |
| Dimensions - Panel cut out |
 |
| Dimensions - Terminations / Output law |
 |
| Model number | ||||||||||||
|
| *1 | Product number | 45LT-R2 : 45LT-R2 Series |
| *2 | Connector type | CN0 : B4B-EH |
| *3 | Output law | B : Linear taper |
| *4 |
Total resistance |
10K : 10kohm 50K : 50kohm |
| Products No. ( X: Standard model) |
Travel | Output law | Resistance | Mounting screws | Terminal style | |
| 45LT-R2-CN0-B10K | X | 44mm | Linear | 10kohm | M3 | Connector |
| 45LT-R2-CN0-B50K | X | 44mm | Linear | 50kohm | M3 | Connector |
| Replacement model | Photo | Connector | Compatible with replacement crossfader |
| 45L-R2-CN1-B50K |
- |
22-27-2041 (Molex) S4B-PH (JST) |
Vestax CF-PCV (Switch mode "PMC") and other models. |
 |
|||
| Update list | |
| 2024.01.29. | Addition of replacement model. |
| 2023.12.19. | Addition of maximum input voltage specification. |
| 2023.07.20. | Slight correction of specification notations. |
| 2023.01.25. | Specification change [Travel (45 => 44), Residual resistance (5ohm => 60ohm), Correction of typographical errors. |
| 2022.11.08. | First edition |