English   Japanese   
TOP         PRODUCTS         TECHNOLOGY         DISTRIBUTORS         PRODUCT STATUS

     VARIABLE ATTENUATOR

CP2511 Series
Conductive plastic resistor element used (Low rotational noise).
25mm square body.
315 degree operating angle.
Highly dustproof.
Maximum number of interlocking circuits: 8
Last update: 2023.03.22. [Electrical-spec] [Mechanical-spec] [Note] [Dimensions] [Model-number] EU-RoHS


Information
This product is constructed by a ladder circuit. Cannot use it for a rheostat use (Cannot use to change a resistance level).

Electrical specifications CP2511 Series
Products *CP2511*-*
Attenuation direction
[Load: high]


 
CCW (Large attenuation & cut off) - CW (Small attenuation)
Degrees
(CCW to CW)
315300285270255240225210195 1801651501351201059075604530 150
Attenuation
[dB]
Cut-off50423734323028 26 2422201816141210864 20
Circuit method Ladder circuit
Total resistance (1-C) 5kohm,   10kohm,   50kohm,   100kohm
Total resistance tolerance ±20%
Attenuation accuracy
[Load: high]
 
0 - 10dB: ±1.0dB
   - 30dB: ±2.0dB
   - 42dB: ±3.0dB
Matching accuracy
 [Load: High]
 
0 - 10dB: 1.0dB
   - 30dB: 1.5dB
   - 42dB: 2.5dB
Insertion loss 0.5dB or less
Cut off [15kHz] 85dB Min.
Voltage proof 1 Min. at AC500V
Insulation resistance 50Mohm or more at DC500V
Max rating DC20V (0.1W)
Sliding noise level 47mV or less (by JIS C 6443)
Rotational life 100,000 Cycles Min. (18cycles/min, Sliding noise level: Less than 100mV)
* [Load: high]    The output side load should be used with high impedance (20 times or more than the total resistance value).

Mechanical specifications CP2511 Series
Operating angle 315 degrees ±5 degrees
Rotational torque 0.1 to 1.5Ncm (Different by number of circuit)
Strength Nut-Attached 50Ncm
Attached parts Hexagonal nut (M9)
Stopper strength 50Ncm
Push-pull strangth 50N


General specifications CP2511 Series
Temperature range -10 to +70 degrees C (Operating), -15 to +75 degrees C (Storage)
Relative humidity 90%RH (No condensation)

Note
* Solder heat resistance: 350deg C max, 5sec max, 2 times. (Manual soldering only)
* Special order of the shaft length is possible. Please contact us for details.
* It is highly recommended that the fault tolerant system is to be set up in the big situation like the live broadcast.
* Replacing it from other brands tests it enough, and please consider.
* Caution in Ladder circuit use.

   Important points in using audio curve and log curve of TKD faders >>
* If distortion rate is a concern, consider the potentiometer circuit type.

Dimensions - CP2511*-*
CP2511 2CP2511 3CP2511 4CP2511
5CP2511 6CP2511 7CP2511 8CP2511


Dimensions - Terminations

Model number
2 CP2511 S - 10K
*1 *2 *3   *4


*1
 
Number of circuits
 
Blank : Single circuit
2 to 8  : Number of circuits specified
*2 Product number CP2511 : CP2511 Series
*3
 
Mechanical click option
 
Blank : Without click
S         : With click (15degrees step)
*4


 
Total resistance


 
5K     :   5kohm
10K   : 10kohm
50K   : 50kohm
100K : 100kohm


Products No.
( X: Standerd model)
Number of circuits Output law Resistance Click Shaft diameter x Shaft length
CP2511-5K X 1 Audio 5kohm Without Φ6 x 20mm
CP2511-10K X 1 Audio 10kohm Without Φ6 x 20mm
CP2511-50K X 1 Audio 50kohm Without Φ6 x 20mm
CP2511-100K X 1 Audio 100kohm Without Φ6 x 20mm
CP2511S-5K X 1 Audio 5kohm With Φ6 x 20mm
CP2511S-10K X 1 Audio 10kohm With Φ6 x 20mm
CP2511S-50K X 1 Audio 50kohm With Φ6 x 20mm
CP2511S-100K X 1 Audio 100kohm With Φ6 x 20mm
2CP2511-5K X 2 Audio 5kohm Without Φ6 x 20mm
2CP2511-10K X 2 Audio 10kohm Without Φ6 x 20mm
2CP2511-50K X 2 Audio 50kohm Without Φ6 x 20mm
2CP2511-100K X 2 Audio 100kohm Without Φ6 x 20mm
2CP2511S-5K X 2 Audio 5kohm With Φ6 x 20mm
2CP2511S-10K X 2 Audio 10kohm With Φ6 x 20mm
2CP2511S-50K X 2 Audio 50kohm With Φ6 x 20mm
2CP2511S-100K X 2 Audio 100kohm With Φ6 x 20mm
3CP2511-5K X 3 Audio 5kohm Without Φ6 x 20mm
3CP2511-10K X 3 Audio 10kohm Without Φ6 x 20mm
3CP2511-50K X 3 Audio 50kohm Without Φ6 x 20mm
3CP2511-100K X 3 Audio 100kohm Without Φ6 x 20mm
3CP2511S-5K X 3 Audio 5kohm With Φ6 x 20mm
3CP2511S-10K X 3 Audio 10kohm With Φ6 x 20mm
3CP2511S-50K X 3 Audio 50kohm With Φ6 x 20mm
3CP2511S-100K X 3 Audio 100kohm With Φ6 x 20mm
4CP2511-5K X 4 Audio 5kohm Without Φ6 x 20mm
4CP2511-10K X 4 Audio 10kohm Without Φ6 x 20mm
4CP2511-50K X 4 Audio 50kohm Without Φ6 x 20mm
4CP2511-100K X 4 Audio 100kohm Without Φ6 x 20mm
4CP2511S-5K X 4 Audio 5kohm With Φ6 x 20mm
4CP2511S-10K X 4 Audio 10kohm With Φ6 x 20mm
4CP2511S-50K X 4 Audio 50kohm With Φ6 x 20mm
4CP2511S-100K X 4 Audio 100kohm With Φ6 x 20mm
5CP2511-5K   5 Audio 5kohm Without Φ6 x 20mm
5CP2511-10K   5 Audio 10kohm Without Φ6 x 20mm
5CP2511-50K   5 Audio 50kohm Without Φ6 x 20mm
5CP2511-100K   5 Audio 100kohm Without Φ6 x 20mm
5CP2511S-5K   5 Audio 5kohm With Φ6 x 20mm
5CP2511S-10K   5 Audio 10kohm With Φ6 x 20mm
5CP2511S-50K   5 Audio 50kohm With Φ6 x 20mm
5CP2511S-100K   5 Audio 100kohm With Φ6 x 20mm
6CP2511-5K   6 Audio 5kohm Without Φ6 x 20mm
6CP2511-10K   6 Audio 10kohm Without Φ6 x 20mm
6CP2511-50K   6 Audio 50kohm Without Φ6 x 20mm
6CP2511-100K   6 Audio 100kohm Without Φ6 x 20mm
6CP2511S-5K   6 Audio 5kohm With Φ6 x 20mm
6CP2511S-10K   6 Audio 10kohm With Φ6 x 20mm
6CP2511S-50K   6 Audio 50kohm With Φ6 x 20mm
6CP2511S-100K   6 Audio 100kohm With Φ6 x 20mm
7CP2511-5K   7 Audio 5kohm Without Φ6 x 20mm
7CP2511-10K   7 Audio 10kohm Without Φ6 x 20mm
7CP2511-50K   7 Audio 50kohm Without Φ6 x 20mm
7CP2511-100K   7 Audio 100kohm Without Φ6 x 20mm
7CP2511S-5K   7 Audio 5kohm With Φ6 x 20mm
7CP2511S-10K   7 Audio 10kohm With Φ6 x 20mm
7CP2511S-50K   7 Audio 50kohm With Φ6 x 20mm
7CP2511S-100K   7 Audio 100kohm With Φ6 x 20mm
8CP2511-5K   8 Audio 5kohm Without Φ6 x 20mm
8CP2511-10K   8 Audio 10kohm Without Φ6 x 20mm
8CP2511-50K   8 Audio 50kohm Without Φ6 x 20mm
8CP2511-100K   8 Audio 100kohm Without Φ6 x 20mm
8CP2511S-5K   8 Audio 5kohm With Φ6 x 20mm
8CP2511S-10K   8 Audio 10kohm With Φ6 x 20mm
8CP2511S-50K   8 Audio 50kohm With Φ6 x 20mm
8CP2511S-100K   8 Audio 100kohm With Φ6 x 20mm


Custom model number
[ How to specify different output-law in multiple circuits ]
* The number in front of CP2511 is the total number of circuits.
* The first output-law specified in the beginning will be the knob side.
* Consecutive cases of the same output-law are combined into one. ( A10K / A10K >>>> 2-A10K )
* If the total resistance is different, specify it separately.
* The CP2500 Series cannot be mounted because the angle is different.


[Please refer to the following]
Example Number of circuits Output law types Circuit position Model number for this specification.
1
 
4 circuits
 
Ladder 10kohm x2
Ladder 5kohm x2
top (knob side)
bottom
4CP2511 - 2-10K / 2-5K
 
2
 
3 circuits
 
Ladder 10kohm x1
Ladder 100kohm x2
top (knob side)
bottom
3CP2511 - 10K / 2-100K
 
3

 
3 circuits

 
Ladder 10kohm x1
Ladder 5kohm x1
Ladder 10kohm x1
top (knob side)
center
bottom
3CP2511 - 10K / 5K / 10K

 




Update list
   
2023.03.22. Additional 3D data (step format).
2022.11.07. First edition