| MOTORIZED CONTROL FADER |
 |
MF-9101PFL Series |
| Conductive plastic resistor element used (Low slide noise). With Pre-Fade Listen switch. Horizontal style control-bar design (Protection against dust). Durable system which adopted the shaft of the high quality. With touch sense track. |
| Last update: 2023.01.01. | [Electrical-spec] | [Mechanical-spec] | [Note] | [Dimensions] | [Model-number] | EU-RoHS |
| Information |
| Due to a delay in parts
procurement, the color of the main body (label side) has been changed to
gray. This will not affect the use of the product. If you cannot change the color, please contact our sales department. |
| Electrical specifications | MF-9101PFL Series |
| Products | MF-9101PFL-B*-* |
| Number of circuits Type of output laws |
1 Linear taper |
| Circuit method | Potentiometer circuit |
| Total resistance (1-3) | 10kohm, 5kohm |
| Total resistance tolerance | ±20% |
| Linearity | ±5% (Linear taper) |
| Residual resistance (1-2), (2-3) | 30ohm or less (Linear taper) |
| Touch sence track contact resistance (4-Control-bar) |
20ohm or less |
| PFL sence switch contact resistance (N.O.-C) |
50ohm or less |
| Voltage proof | 1 Min. at AC500V |
| Insulation resistance | 50Mohm or more at DC500V |
| Max rating | DC20V (0.1W) |
| Sliding noise level | 47mV or less (by JIS C 6443) |
| Sliding life | 100,000 Cycles Min. (18cycles/min, Sliding noise level: Less than 100mV) |
| Drive motor data |
DC12V Coreless motor : Input voltage: DC12V, Stall
current: 0.55A or less [12CL-3035 (Custom-made for TKD.) : Orbray Co., Ltd.] DC8V Iron cored motor : Input voltage: DC5V - 11.5V (Nominal DC8V), Stall current: 0.5A or less [FF-050SB-09250 : MABUCHI MOTOR Co., Ltd.] |
| Mechanical specifications | MF-9101PFL Series |
| Travel (Stroke) length | 100mm ±0.5mm (Variable resistance 98mm + PFL switch 2mm) |
| Operating force | 0.1 to 0.3N |
| PFL spring return switch push strength |
5.5 to 7.0N |
| Strength Nut-Attached | 100Ncm |
| Attached parts | M3 screw (Length: Panel thickness + 3mm) |
| Stopper strength | 40N |
| Push-pull strangth | 40N |
| Alignment to the center | ±0.5mm (State not to pressure control-bar, Measurement position: Mounting surface) |
| General specifications | MF-9101PFL Series |
| Temperature range | -10 to +50 degrees C (Operating), -15 to +60 degrees C (Storage) |
| Relative humidity | 80%RH (No condensation) |
| Note |
| * Solder heat resistance: 350deg C max, 5sec max, 2 times. (Manual
soldering only) * Please take care during soldering that the smoke from the solder does not flow inside a fader. * If the flux sticks to a resistor board, it may cause a trouble with the fader. |
| * Move to one end in Control-bar on the occasion of knob wearing, and can break into it slowly. |
| * It is highly recommended that the fault tolerant system is to be set up in the big situation like the live broadcast. |
| *
This product is designed on the assumption of the horizontal use. * The enough operational testing is highly recommended for the slant or the vertical use to prevent the unexpected operation. |
| * Replacing it from other brands tests it enough, and please consider. |
| Dimensions - MF-9101PFL-*-J12 |
 |
| Dimensions - MF-9101PFL-**-M8V |
 |
| Dimensions - Panel cut out |
 |
| Dimensions - Terminations |
 |
| Dimensions - Pre-fade Listen |
 |
| Model number | ||||||||||||
|
| *1 | Product number | MF-9101PFL : MF-9101PFL Series |
| *2 | Output law | B : Linear taper + PFL switch
track + Touch sence track |
| *3 |
Total resistance |
10K : 10kohm 5K : 5kohm |
| *4 |
DC Motor type |
J12 : DC12V Coreless M8V : DC8V Iron cored |
| Products No. ( X: Standerd model) |
Travel | Output law | Resistance | PFL | Touch sence track |
Motor | Mounting Screws |
Control-bar length (Bracket height) |
|
| MF-9101PFL-B10K-J12 | X | 100mm (98mm+2mm) |
Linear | 10kohm | With | With | DC12V Coreless |
M3 | 9mm (5mm) |
| MF-9101PFL-B5K-J12 | 100mm (98mm+2mm) |
Linear | 5kohm | With | With | DC12V Coreless |
M3 | 9mm (5mm) | |
| MF-9101PFL-B10K-M8V | X | 100mm (98mm+2mm) |
Linear | 10kohm | With | With | DC8V iron cored |
M3 | 9mm (5mm) |
| MF-9101PFL-B5K-M8V | 100mm (98mm+2mm) |
Linear | 5kohm | With | With | DC8V iron cored |
M3 | 9mm (5mm) | |
| Update list | |
| 2023.01.01. | Change of company name. [Adamant Namiki Precision Jewel Co., Ltd. → Orbray Co., Ltd.] |
| 2022.11.01. | First edition |